Optoma EP771 Especificações

Table of Contents 1 Table of Contents Table of Contents...

Introduction Rear view ITEM LABEL DESCRIPTION SEE PAGE:1. Rear IR Re-ceiver Receiver for IR signal from remote control. 2. DVI-D Connect the c

Introduction 11 ITEM LABEL DESCRIPTION SEE PAGE:14. Power switch Turns the power on and off 4315. Power Connect the supplied power cord 16. S

Introduction Bottom view ITEM LABEL DESCRIPTION SEE PAGE: 1. Ceiling support holes. Contact your dealer for information on mounting your project

Introduction Remote Control Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo-rescent

Introduction 14 ITEM LABEL DESCRIPTION SEE PAGE: 3. Laser Press to operate the on-screen pointer 4. Up Up arrow when connected through USB to

Introduction 15 ITEM LABEL DESCRIPTION SEE PAGE: 25. Left Left arrow when connected through USB to a PC 26. Enter Enter key when connected thr

Introduction Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow. 2. I

Setup and Operation Setup and Operation Connecting Input Devices A PC or notebook computer as well as video devices can be connected to the projector

Setup and Operation 18 ITEM LABEL DESCRIPTION USB Connect the supplied USB cable from a computer for USB mouse func-tion and firmware upgrades.

Setup and Operation Starting and Shutting down the Projector 1. Slide the lens cover. 2. Connect the power cord to the projector [A] Connect the ot

Table of Contents 2 LED Error Messages ...

Setup and Operation 7. When the “Power Off? / Press Power again” message appears, press the Power button. The projector will turn off. 8. Turn off

Setup and Operation Setting an Access Password (Security Lock) You can use the cursor (arrow) buttons to set a password and prevent unauthorized use

Setup and Operation 6. Every time you start the projector, a password dialog box appears. Enter the password in the order you set it on step 5. (Pre

Setup and Operation Adjusting the Projector Level Take note of the following when setting up the projector: • The projector table or stand should be

Setup and Operation Adjusting the Zoom, Focus and Keystone 1. Use the Image-zoom control (on the projector only) to resize the pro-jected image and

Setup and Operation OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD

Setup and Operation Setting the OSD Language You may want to reference the OSD on your projector while reading this section. Set the OSD lan-guage to

Menu Setting Menu Setting OSD Menu Overview Use the following illustration* to quickly find a setting or determine the range for a setting. * Repre

Menu Setting Image Menu Press the Menu button to open the OSD menu.* Press the cursor button to move to the Image menu. Press the cursor button t

Menu Setting 29 ITEM DESCRIPTION DEFAULT Sharpness Press the cursor button to adjust the display sharpness (Range: 1-5) 3 Color Temperature Pre

Usage Notice 3 Usage Notice Congratulations and thank you for choosing an EP771 projector, an on Optoma product. This product is an XGA single chip 0

Menu Setting Display Menu Press the Menu button to open the OSD menu. Press the cursor button to move to the Display menu. Press the cursor butto

Menu Setting 31 ITEM DESCRIPTION DEFAULT Digital Zoom Digital operation for zoom and pan adjustment. Press Enter or . The Zoom menu appears. Press

Menu Setting Setup Menu Press the Menu button to open the OSD menu. Press the cursor button to move to the Setup menu. Press the cursor button to

Menu Setting 33 ITEM DESCRIPTION DEFAULT Volume Press the cursor button to adjust the audio volume level. (Range: 0 – 8) 4 Source Lock Enable o

Menu Setting 34 Setup Menu Functions Available for Connected SourceFunction RGB DVI Component Video Composite Video S-Video Projection Type O O O

Menu Setting Color setting Menu Press the Menu button to open the OSD menu. Press the cursor button to move to the Color setting menu. Press the c

Menu Setting Language Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Lan-guage menu. Press the cursor b

Menu Setting Management Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Man-agement menu. Press the curso

Menu Setting 38 ITEM DESCRIPTION DEFAULT Translucent Menu Press the cursor button to select OSD back-ground translucent level. (Range: 0% – 25%

Appendices Appendices Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certi

Usage Notice Power Safety  Only use the supplied power cord.  Do not place anything on the power cord. Place the power cord where it will not be in

Appendices Open the lamp com-partment cover (B). B 2. 40 3. Remove the two screws from the lamp module (C). Lift the module handle up (D). CD 4.

Appendices Pull firmly on the module handle to re-move the lamp module (D) D 5. Reverse steps 1 to 5 to install the new lamp module. 6. 41

Appendices Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. Press the Menu but

Appendices Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure trouble-free operation. Warning: 1. Be sure to tu

Appendices 44 Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the p

Appendices 45 LED Error Messages ERROR CODE MESSAGE POWER LED/FLASHES READY LED/FLASHES Lamp usage task created error 2 1 Environment usage task

Appendices 46 Image Problems Problem: No image appears on the screen 1. Verify the settings on your notebook or desktop PC. 2. Turn off all equipme

Appendices 47 Remote Control Problems Problem: The projector does not respond to the remote control 1. Direct the remote control towards remote sen

Appendices 48 Having the Projector Serviced If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the

Specifications Specifications Projection Distance V.S. Projection Size ABCDLecnatsiD noitcejorP Anchura de pantalla Altura de pantalla Distancia

Usage Notice 5 Main Features • Lightweight unit, easy to pack away and transport • Compatible with all major video standards including NTSC, PAL, a

Specifications 50 Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed

Specifications Projector Dimensions 300 mm (11.8”)108 mm (4.3”) 244 mm (9.6”)51

Regulatory Compliance 52 Regulatory Compliance FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital d

Copyright This publication, including all photographs, illustrations and software, is protected under international copy-right laws, with all right

Introduction Introduction Packing Checklist Carefully unpack the projector and check that the following items are included: EP771 PROJECTOR REMOTE

Introduction Views of Projector Front-right View 1765 43823 ITEM LABEL DESCRIPTION SEE PAGE: 1. Focus Focuses the projected image 242. Lens zoo

Introduction Top view—On-screen Display (OSD) buttons and LEDs 811 10 91743625 ITEM LABEL DESCRIPTION SEE PAGE: 1. Keystone/ Down cursorCorrects

Introduction 9 ITEM LABEL DESCRIPTION SEE PAGE: 6. RE-SYNC Optimizes image size, position, and resolution 197. Menu Opens and exits the OSD 25